Jump to content

Bad sector

From Wikipedia, the free encyclopedia
Hard disk reader

A bad sector in computing is a disk sector on a disk storage unit that is unreadable. Upon taking damage, all information stored on that sector is lost. When a bad sector is found and marked, the operating system like Windows or Linux will skip it in the future. Bad sectors are a threat to information security in the sense of data remanence.

Details

[edit]

Bad sectors can be "soft" (logical) or "hard" (hardware, physical), depending on what is making the sector inaccessible. In case of power loss, bit rot (more likely on floppy disks), or firmware issues, the on-disk format can be corrupt beyond what the error correcting code can fix. This is a "soft" bad sector: writing over the corruption would succeed.[1]

On the other hand, sectors broken physically cannot be restored: writing would fail, forcing a remap. A new drive may start with some innocuous bad sectors due to manufacturing flaws. Larger patches occur throughout use, due to head crash, wear-and-tear, physical shock, or dust intrusion.[2][1]

On solid-state drives, flash wear or flash controller error may also cause bad sectors.[3]

Handling

[edit]

Operating system

[edit]

Bad sectors may be detected by the operating system or the disk controller. Most file systems contain provisions for sectors to be marked as bad, so that the operating system avoids them in the future. Disk diagnostic utilities, such as CHKDSK (Microsoft Windows), Disk Utility (on macOS), or badblocks (on Linux) can actively look for bad sectors upon user request.

With the advent of SMART-enabled disk controllers (see below), the burden of avoiding bad sectors more commonly falls to the disk.[4] Some newer file systems such as Btrfs and ZFS do not have a bad-block avoidance feature at all.[5] Software tools that look for bad blocks still have a use case: by issuing writes at detected bad sectors, one can expedite the remapping process, avoiding further attempts at reading the bad sector.[6]

Disk controller

[edit]

When a sector is found to be bad or unstable by the firmware of a disk controller, a modern (post-1990) disk controller remaps the logical sector to a different physical sector. Typically, automatic remapping of sectors only happens when a sector is written to – failed reads remain marked "pending". In the normal operation of a hard drive, the detection and remapping of bad sectors should take place in a manner transparent to the rest of the system and in advance before data is lost. There are two types of remapping by disk hardware: P-LIST (mapping during factory production tests) and G-LIST (mapping during consumer usage by disk microcode).[4]

Utilities can read the Self-Monitoring, Analysis, and Reporting Technology (SMART) information to tell how many sectors have been reallocated, and how many spare sectors the drive may still have.[7] Because reads and writes from G-list sectors are automatically redirected (remapped) to spare sectors, it slows down drive access even if data in drive is defragmented. Once the G-list is filled up, the storage unit must be replaced.[8][9]

Compared to ATA, the SCSI command set allows finer-grained management of bad sectors. Users can read the G-LIST, control whether automatic remap is performed, and use a dedicated command REASSIGN BLOCKS to manually remap if needed. The command set also provides a way to perform low-level format with FORMAT UNIT.[10]

Manipulation methods

[edit]

The Windows program ATATool can be used to create deliberate "soft" bad sectors by manipulating the sector Error correction code (ECC) data. This can be used to verify bad sector support in disk utilities and forensic tools. For instance, to make sector 10 bad:

ATATOOL /BADECC:10 \\.\PhysicalDrive1

hdparm has a --make-bad-sector command that works similarly. For newer drives, it can alternatively use WRITE_UNCORRECTABLE_EXT to "flag" a sector as bad: the drive controller would not attempt to read, but fail immediately.[6]

Frequency

[edit]

In a 2007 study, CERN observed 1.53 million hard drives from 30 models over 32 months and analyzed the drive read errors returned. They noted that 3.5% of drives developed "latent read error" (i.e. unreadable bad sector), and that a disk with a bad sector is more likely to develop more. Bad sectors cluster spatially (in a 10–MB neighborhood) and temporally. Errors recovered by ECC, which are reported by enterprise drives (using the SCSI command set), also suggest a higher chance of a bad sector in the future.[11]

See also

[edit]
  • Spiradisc - a copy protection scheme writing sectors on spiraling paths on the disk rather than in concentric circles.
  • Sector slipping – a method of avoiding bad sectors
  • ARccOS Protection – bad sector protection on DVDs, used by Sony.
  • Head crash - a more serious form of damage to the hard disk platter

References

[edit]
  1. ^ a b Zhang (2 March 2018). "Hard vs Soft Bad Sectors in HDD: Different Causes and Solutions". Data Recovery Blog.
  2. ^ Chris Hoffman (5 July 2017). "Bad Sectors Explained: Why Hard Drives Get Bad Sectors and What You Can Do About It". How-To Geek.
  3. ^ "Question - should i rma my 980 pro". Tom's Hardware Forum. 14 February 2023. Retrieved 22 July 2024.
  4. ^ a b "Bad Sector Remapping". mjm.co.uk. Archived from the original on 10 March 2018. Retrieved 9 March 2018.
  5. ^ "badblocks - Can btrfs track / avoid bad blocks?". Unix & Linux Stack Exchange.
  6. ^ a b hdparm(8) – Linux Programmer's Manual – Administration and Privileged Commands. "--make-bad-sector Deliberately create a bad sector (aka. "media error") on the disk. [...] Note also that the --repair-sector option can be used to restore (any) bad sectors when they are no longer needed, including sectors that were genuinely bad (the drive will likely remap those to a fresh area on the media). --write-sector: This can be used to force a drive to repair a bad sector (media error)."
  7. ^ Monitoring Hard Disks with SMART.Linux Journal, 2004.
  8. ^ "Encyclopedia". PCMag.com. Ziff Davis.
  9. ^ Stephens, Curtis E, ed. (11 December 2006), Information technology - AT Attachment 8 - ATA/ATAPI Command Set (ATA8-ACS), working draft revision 3f (PDF), ANSI INCITS, pp. 198–213, 327–344, archived from the original (PDF) on 30 July 2007
  10. ^ "INCITS 506-202x - Information technology - SCSI Block Commands - 4 (SBC-4) draft revision 22". 15 September 2020. Retrieved 22 May 2023.
  11. ^ Lakshmi N. Bairavasundaram; Garth R. Goodson; Shankar Pasupathy; Jiri Schindler (June 2007). "An analysis of latent sector errors in disk drives". Proceedings of the 2007 ACM SIGMETRICS international conference on Measurement and modeling of computer systems. San Diego, California, United States: ACM. pp. 289–300. CiteSeerX 10.1.1.63.1412. doi:10.1145/1254882.1254917. ISBN 9781595936394. S2CID 14164251. Retrieved 9 June 2012.
[edit]