In radiative heat transfer, a view factor, , is the proportion of the radiation which leaves surface that strikes surface . In a complex 'scene' there can be any number of different objects, which can be divided in turn into even more surfaces and surface segments.

Intensity of thermal radiation from the sun depends on view factor

View factors are also sometimes known as configuration factors, form factors, angle factors or shape factors.

Relations

edit

Summation

edit

Radiation leaving a surface within an enclosure is conserved. Because of this, the sum of all view factors from a given surface,  , within the enclosure is unity as defined by the summation rule

 

where   is the number of surfaces in the enclosure.[1]: 864  Any enclosure with   surfaces has a total   view factors.

For example, consider a case where two blobs with surfaces A and B are floating around in a cavity with surface C. All of the radiation that leaves A must either hit B or C, or if A is concave, it could hit A. 100% of the radiation leaving A is divided up among A, B, and C.

Confusion often arises when considering the radiation that arrives at a target surface. In that case, it generally does not make sense to sum view factors as view factor from A and view factor from B (above) are essentially different units. C may see 10% of A 's radiation and 50% of B 's radiation and 20% of C 's radiation, but without knowing how much each radiates, it does not even make sense to say that C receives 80% of the total radiation.

Reciprocity

edit

The reciprocity relation for view factors allows one to calculate   if one already knows   and is given as

 

where   and   are the areas of the two surfaces.[1]: 863 

Self-viewing

edit

For a convex surface, no radiation can leave the surface and then hit it later, because radiation travels in straight lines. Hence, for convex surfaces,  [1]: 864 

For concave surfaces, this doesn't apply, and so for concave surfaces  

Superposition

edit

The superposition rule (or summation rule) is useful when a certain geometry is not available with given charts or graphs. The superposition rule allows us to express the geometry that is being sought using the sum or difference of geometries that are known.

  [2]

View factors of differential areas

edit
 
Two differential areas in arbitrary configuration

Taking the limit of a small flat surface gives differential areas, the view factor of two differential areas of areas   and   at a distance s is given by:

 

where   and   are the angle between the surface normals and a ray between the two differential areas.

The view factor from a general surface   to another general surface   is given by:[1]: 862 

 

Similarly the view factor   is defined as the fraction of radiation that leaves   and is intercepted by  , yielding the equation  The view factor is related to the etendue.

Example solutions

edit

For complex geometries, the view factor integral equation defined above can be cumbersome to solve. Solutions are often referenced from a table of theoretical geometries. Common solutions are included in the following table:[1]: 865 

Table 1: View factors for common geometries
Geometry Relation
Parallel plates of widths,   with midlines connected by perpendicular of length    

where  

Inclined parallel plates at angle,  , of equal width,  , and a common edge  
Perpendicular plates of widths,   with a common edge  
Three sided enclosure of widths,    

Nusselt analog

edit
 
Nusselt analog: the projected solid angle

A geometrical picture that can aid intuition about the view factor was developed by Wilhelm Nusselt, and is called the Nusselt analog. The view factor between a differential element dAi and the element Aj can be obtained projecting the element Aj onto the surface of a unit hemisphere, and then projecting that in turn onto a unit circle around the point of interest in the plane of Ai. The view factor is then equal to the differential area dAi times the proportion of the unit circle covered by this projection.

The projection onto the hemisphere, giving the solid angle subtended by Aj, takes care of the factors cos(θ2) and 1/r2; the projection onto the circle and the division by its area then takes care of the local factor cos(θ1) and the normalisation by π.

The Nusselt analog has on occasion been used to actually measure form factors for complicated surfaces, by photographing them through a suitable fish-eye lens.[3] (see also Hemispherical photography). But its main value now is essentially in building intuition.

See also

edit
  • Radiosity, a matrix calculation method for solving radiation transfer between a number of bodies.
  • Gebhart factor, an expression to solve radiation transfer problems between any number of surfaces.

References

edit
  1. ^ a b c d e Incropera, Frank P.; DeWitt, David P.; Bergman, Theodore L.; Lavine, Adrienne S., eds. (2013). Principles of heat and mass transfer (7. ed., international student version ed.). Hoboken, NJ: Wiley. ISBN 978-0-470-50197-9.
  2. ^ Heat and Mass Transfer, Yunus A. Cengel and Afshin J. Ghajar, 4th Edition
  3. ^ Michael F. Cohen, John R. Wallace (1993), Radiosity and realistic image synthesis. Morgan Kaufmann, ISBN 0-12-178270-0, p. 80
edit

A large number of 'standard' view factors can be calculated with the use of tables that are commonly provided in heat transfer textbooks.