File:Usbkey internals edit.jpg
From Wikimedia Commons, the free media repository
Jump to navigation
Jump to search
Size of this preview: 586 × 599 pixels. Other resolutions: 235 × 240 pixels | 469 × 480 pixels | 887 × 907 pixels.
Original file (887 × 907 pixels, file size: 127 KB, MIME type: image/jpeg)
File information
Structured data
Captions
Summary
[edit]DescriptionUsbkey internals edit.jpg |
English: This photograph shows both sides of the printed circuit board inside a typical keydrive (circa 2004), in this case an inexpensive 64 Mbyte USB2.0 device. The plastic clamshell case has been removed. In practice the keydrive consists of only two significant components. The first is the flash memory part (item 4 in the diagram), a generic device that might as easily be found in a digital camera's memory card. The second (item 2 in the diagram) is a device which implements the USB networking and mass-storage interface, and which knows how to make a chunk of generic flash memory appear like a normal disk drive. The high degree of integration in this latter part makes small, inexpensive keydrives possible. The parts of the device are as follows: # A male type-A USB connector. # An Ours Technology Inc. OTi-2168 USB 2.0 mass storage controller. This implements the USB 2.0 host controller, and provides a seamless linear interface to block-oriented serial flash devices, while hiding the complexities of block-orientation, block erasure, and wear balancing. It contains a small RISC microprocessor and a small amount of ROM and RAM. This communicates with the Hynix device over an 8-line unified address/data bus. # JP1 and JP2: two unpopulated 10-pin connectors, used for testing during the keydrive's manufacture. # A Hynix Semiconductor HY27USxx121M series NAND Flash memory device, featuring 4096 independently erasable blocks each providing 16 Kbytes of storage, yielding a total of 64 Mbytes of usable storage. The version used in this keydrive is a 20x12mm 48-pin TSOP1 (Thin Small Outline Package) surface-mount package (info) (datasheet). # An SKC Shin Chang Electronics 12.000 MHz crystal oscillator (XTAL). The OTi device runs the output of this through a phase-locked loop to produce its main 12 MHz clock signal. # A single yellow light-emitting diode (run from a pin on the OTi device) which flashes to indicate activity. # A simple two-position switch, used to indicate whether the device should be in "write-protect" mode. It is shown here in the make position, indicating write-protect is off. # An unpopulated space for a second TSOP1 memory package. The OTi device is capable of driving up to eight such devices. Having this second space allows the manufacturer to choose (generally on a cost basis) whether to use one or two TSOP flash parts. Surrounding these main components are a number of tiny surface-mount resistors (many of them serving as pull-ups) and capacitors. For a closeup of an area of this keydrive, see this image. Photographs taken and annotated by John Fader in December 2004 using Adobe Photoshop and Inkscape. This image is (C) Copyright 2004 and (with the exception of its use under the GFDL) all rights are reserved. Originally uploaded by John Fader 17:59, 4 December 2004 |
Date | |
Source | http://www.costar.com.tw/pdf/ |
Author | John Fader |
John Fader, the copyright holder of this work, hereby publishes it under the following license:
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is included in the section entitled GNU Free Documentation License.http://www.gnu.org/copyleft/fdl.htmlGFDLGNU Free Documentation Licensetruetrue |
This file is licensed under the Creative Commons Attribution-Share Alike 3.0 Unported license. | ||
Attribution: John Fader | ||
| ||
This licensing tag was added to this file as part of the GFDL licensing update.http://creativecommons.org/licenses/by-sa/3.0/CC BY-SA 3.0Creative Commons Attribution-Share Alike 3.0truetrue |
File history
Click on a date/time to view the file as it appeared at that time.
Date/Time | Thumbnail | Dimensions | User | Comment | |
---|---|---|---|---|---|
current | 16:51, 8 February 2007 | 887 × 907 (127 KB) | Jrockley (talk | contribs) | ==The internal components of a typical keydrive== This photograph shows both sides of the printed circuit board inside a typical keydrive (circa 2004), in this case an inexpensive 64 Mbyte USB2.0 device. The plastic clamshell case has been remove |
You cannot overwrite this file.
File usage on Commons
There are no pages that use this file.
File usage on other wikis
The following other wikis use this file:
- Usage on de.wikibooks.org
- Usage on en.wikipedia.org
- Usage on fr.wikipedia.org
- Usage on id.wikipedia.org
- Usage on sr.wikipedia.org
- Usage on zh.wikipedia.org
Metadata
This file contains additional information such as Exif metadata which may have been added by the digital camera, scanner, or software program used to create or digitize it. If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of the original file. The timestamp is only as accurate as the clock in the camera, and it may be completely wrong.
_error | 0 |
---|