-
Error Determination in Sextupole Magnet Calibration and Alignment Measurements and Application to Horizontal Beam Size Calculations at the Cornell Electron-positron Storage Ring
Authors:
James A. Crittenden,
Georg H. Hoffstaetter,
David C. Sagan
Abstract:
We report on measurements and modeling studies performed from 2021 to 2024 on the 76 sextupole magnets in the Cornell Electron-positron Storage Ring CESR. Beam-based, magnet-specific calibrations ($K_2$ value versus excitation current) were measured. It was found that the new calibrations differ from those previously in use by an average of 3.1% with an RMS spread of 12%. The uncertainties in the…
▽ More
We report on measurements and modeling studies performed from 2021 to 2024 on the 76 sextupole magnets in the Cornell Electron-positron Storage Ring CESR. Beam-based, magnet-specific calibrations ($K_2$ value versus excitation current) were measured. It was found that the new calibrations differ from those previously in use by an average of 3.1% with an RMS spread of 12%. The uncertainties in the calibration correction factors average 1.7% with an RMS spread of 1.0%.
Sextupole alignment values relative to the reference orbit were measured by combining the measured beam position with the quadrupole and skew quadrupole terms caused by a sextupole strength change $ΔK_2$. High accuracy was achieved by fitting to difference phase and coupling functions as $K_2$ was varied. The horizontal (vertical) average offset values were found to be -0.01 (0.03)~mm with RMS spread of 1.1 (0.9)~mm with some exceptionally large values of a few millimeters. Typical uncertainties are 0.01-0.02~mm.
The above measurements were motivated by the precision required in measuring horizontal beam size at each sextupole. A precision of 10\% for a \mbox{1-mm} beam size requires uncertainties of better than 0.1~$μ$radian in the horizontal angle change produced in the sextupole for a typical strength change of \mbox{$ΔK_2 \, L$ = 1 m$^{-2}$}, where $L$ is the length of the sextupole, as well as 10\% in the difference of the squared horizontal and vertical beam positions relative to the center of the sextupole. These precision values were achieved by the analysis of difference functions. However, a small source of horizontal angle change of unknown origin, independent of the sextupole strength, requires a sextupole strength range larger than now available to measure accurately the typical horizontal beam size at CESR.
△ Less
Submitted 29 September, 2024;
originally announced September 2024.
-
Enhanced beam-beam modeling to include longitudinal variation during weak-strong simulation
Authors:
Derong Xu,
Vasiliy S. Morozov,
David Sagan,
Yue Hao,
Yun Luo
Abstract:
Beam-beam interactions pose substantial challenges in the design and operation of circular colliders, significantly affecting their performance. In particular, the weak-strong simulation approach is pivotal for investigating single-particle dynamics during the collider design phase. This paper evaluates the limitations of existing models in weak-strong simulations, noting that while they accuratel…
▽ More
Beam-beam interactions pose substantial challenges in the design and operation of circular colliders, significantly affecting their performance. In particular, the weak-strong simulation approach is pivotal for investigating single-particle dynamics during the collider design phase. This paper evaluates the limitations of existing models in weak-strong simulations, noting that while they accurately account for energy changes due to slingshot effects, they fail to incorporate longitudinal coordinate changes ($z$-variation). To address this gap, we introduce two novel transformations that enhance Hirata's original framework by including both $z$-variation and slingshot effect-induced energy changes. Through rigorous mathematical analysis and extensive weak-strong simulation studies, we validate the efficacy of these enhancements in achieving a more precise simulation of beam-beam interactions. Our results reveal that although $z$-variation constitutes a higher-order effect and does not substantially affect the emittance growth rate within the specific design parameters of the Electron-Ion Collider (EIC), the refined model offers improved accuracy, particularly in scenarios involving the interaction between beam-beam effects and other random diffusion processes, as well as in simulations incorporating realistic lattice models.
△ Less
Submitted 20 June, 2024; v1 submitted 5 March, 2024;
originally announced March 2024.
-
Snowmass21 Accelerator Modeling Community White Paper
Authors:
S. Biedron,
L. Brouwer,
D. L. Bruhwiler,
N. M. Cook,
A. L. Edelen,
D. Filippetto,
C. -K. Huang,
A. Huebl,
T. Katsouleas,
N. Kuklev,
R. Lehe,
S. Lund,
C. Messe,
W. Mori,
C. -K. Ng,
D. Perez,
P. Piot,
J. Qiang,
R. Roussel,
D. Sagan,
A. Sahai,
A. Scheinker,
M. Thévenet,
F. Tsung,
J. -L. Vay
, et al. (2 additional authors not shown)
Abstract:
After a summary of relevant comments and recommendations from various reports over the last ten years, this paper examines the modeling needs in accelerator physics, from the modeling of single beams and individual accelerator elements, to the realization of virtual twins that replicate all the complexity to model a particle accelerator complex as accurately as possible. We then discuss cutting-ed…
▽ More
After a summary of relevant comments and recommendations from various reports over the last ten years, this paper examines the modeling needs in accelerator physics, from the modeling of single beams and individual accelerator elements, to the realization of virtual twins that replicate all the complexity to model a particle accelerator complex as accurately as possible. We then discuss cutting-edge and emerging computing opportunities, such as advanced algorithms, AI/ML and quantum computing, computational needs in hardware, software performance, portability and scalability, and needs for scalable I/O and in-situ analysis. Considerations of reliability, long-term sustainability, user support and training are considered next, before discussing the benefits of ecosystems with integrated workflows based on standardized input and output, and with integrated frameworks and data repositories developed as a community. Last, we highlight how the community can work more collaboratively and efficiently through the development of consortia and centers, and via collaboration with industry.
△ Less
Submitted 22 September, 2022; v1 submitted 15 March, 2022;
originally announced March 2022.
-
Simulating a Positron Converter
Authors:
John Mastroberti,
David Sagan,
Jim Shanks
Abstract:
A model to describe the output particle distribution generated by particles impinging on a planar target has been developed. This model was developed to simulate positron production in the Cornell CESR Linac but can be applied to targets using different types of particles.
To model a specific converter target, the output particle distribution is first simulated by tracking particles using the Ge…
▽ More
A model to describe the output particle distribution generated by particles impinging on a planar target has been developed. This model was developed to simulate positron production in the Cornell CESR Linac but can be applied to targets using different types of particles.
To model a specific converter target, the output particle distribution is first simulated by tracking particles using the Geant4 toolkit which models the fundamental physics of the conversion process. The Monte Carlo distribution from Geant4 is fitted to a set of functions and the function coefficients are saved for use in simulations. Using the fit functions in a simulation is not only more portable but is also more than an order of magnitude faster than running Geant4. This model has been successfully incorporated into the Bmad simulation toolkit.
The output position, angular orientation, and momentum distribution is modeled. Preliminary support for modeling the polarization distribution is also discussed.
△ Less
Submitted 30 December, 2021;
originally announced December 2021.
-
Simulations of Future Particle Accelerators: Issues and Mitigations
Authors:
D. Sagan,
M. Berz,
N. M. Cook,
Y. Hao,
G. Hoffstaetter,
A. Huebl,
C. -K. Huang,
M. H. Langston,
C. E. Mayes,
C. E. Mitchell,
C. -K. Ng,
J. Qiang,
R. D. Ryne,
A. Scheinker,
E. Stern,
J. -L. Vay,
D. Winklehner,
H. Zhang
Abstract:
The ever increasing demands placed upon machine performance have resulted in the need for more comprehensive particle accelerator modeling. Computer simulations are key to the success of particle accelerators. Many aspects of particle accelerators rely on computer modeling at some point, sometimes requiring complex simulation tools and massively parallel supercomputing. Examples include the modeli…
▽ More
The ever increasing demands placed upon machine performance have resulted in the need for more comprehensive particle accelerator modeling. Computer simulations are key to the success of particle accelerators. Many aspects of particle accelerators rely on computer modeling at some point, sometimes requiring complex simulation tools and massively parallel supercomputing. Examples include the modeling of beams at extreme intensities and densities (toward the quantum degeneracy limit), and with ultra-fine control (down to the level of individual particles). In the future, adaptively tuned models might also be relied upon to provide beam measurements beyond the resolution of existing diagnostics. Much time and effort has been put into creating accelerator software tools, some of which are highly successful. However, there are also shortcomings such as the general inability of existing software to be easily modified to meet changing simulation needs. In this paper possible mitigating strategies are discussed for issues faced by the accelerator community as it endeavors to produce better and more comprehensive modeling tools. This includes lack of coordination between code developers, lack of standards to make codes portable and/or reusable, lack of documentation, among others.
△ Less
Submitted 24 August, 2021;
originally announced August 2021.
-
Polarization and Centre-of-mass Energy Calibration at FCC-ee
Authors:
Alain Blondel,
Patrick Janot,
Jörg Wenninger,
Ralf Aßmann,
Sandra Aumon,
Paolo Azzurri,
Desmond P. Barber,
Michael Benedikt,
Anton V. Bogomyagkov,
Eliana Gianfelice-Wendt,
Dima El Kerchen,
Ivan A. Koop,
Mike Koratzinos,
Evgeni Levitchev,
Thibaut Lefevre,
Attilio Milanese,
Nickolai Muchnoi,
Sergey A. Nikitin,
Katsunobu Oide,
Emmanuel Perez,
Robert Rossmanith,
David C. Sagan,
Roberto Tenchini,
Tobias Tydecks,
Dmitry Shatilov
, et al. (3 additional authors not shown)
Abstract:
The first stage of the FCC (Future Circular Collider) is a high-luminosity electron-positron collider (FCC-ee) with centre-of-mass energy ranging from 88 to 365 GeV, to study with high precision the Z, W, Higgs and top particles, with samples of $5 \times 10^{12}$ Z bosons, $10^8$ W pairs, $10^6$ Higgs bosons and $10^6$ top quark pairs. A cornerstone of the physics program lays in the precise (ppm…
▽ More
The first stage of the FCC (Future Circular Collider) is a high-luminosity electron-positron collider (FCC-ee) with centre-of-mass energy ranging from 88 to 365 GeV, to study with high precision the Z, W, Higgs and top particles, with samples of $5 \times 10^{12}$ Z bosons, $10^8$ W pairs, $10^6$ Higgs bosons and $10^6$ top quark pairs. A cornerstone of the physics program lays in the precise (ppm) measurements of the W and Z masses and widths, as well as forward-backward asymmetries. To this effect the centre-of-mass energy distribution should be determined with the high precision. This document describes the capacity offered by FCC-ee, starting with transverse polarization of the beams around the Z pole and the W pair threshold. A running scheme based on regular measurements of the beam energy by resonant depolarization of pilot bunches, during physics data taking, is proposed. The design for polarization wigglers, polarimeter and depolarizer is outlined. The $e^\pm$ beam energies will be monitored with a relative precision of $10^{-6}$. The centre-of-mass energy is derived subject to further corrections, related to the beam acceleration, synchrotron radiation and beamstrahlung; these effects are identified and evaluated. Dimuon events $e^+e^- \to μ^+ μ^-$, recorded in the detectors, provide with great precision the beam crossing angle, the centre-of-mass energy spread, and the $e^+$ and $e^-$ energy difference. Monitoring methods to minimize absolute error and relative uncertainties are discussed. The impact on the physics measurements is given. A programme of further simulations, design, monitoring and R&D is outlined.
△ Less
Submitted 26 September, 2019;
originally announced September 2019.
-
Beam Commissioning Results from the CBETA Fractional Arc Test
Authors:
C. Gulliford,
N. Banerjee,
A. Bartnik,
J. S. Berg,
J. Crittenden,
J. Dobbins,
R. Hulsart,
J. Jones,
D. J. Kelliher,
B. Kuske,
W. Lou,
M. McAteer,
R. Michnoff,
S. Peggs,
P. Quigley,
D. Sagan,
K. Smolenski,
V. Vesherevich,
D. Widger,
G. H. Hoffstaetter,
D. Trbojevic
Abstract:
This work describes first commissioning results from the Cornell Brookhaven Energy Recovery Test Accelerator Fractional Arc Test. These include the recommissioning of the Cornell photo-injector, the first full energy operation of the main linac with beam, as well as commissioning of the lowest energy matching beamline (splitter) and a partial section of the Fixed Field Alternating gradient (FFA) r…
▽ More
This work describes first commissioning results from the Cornell Brookhaven Energy Recovery Test Accelerator Fractional Arc Test. These include the recommissioning of the Cornell photo-injector, the first full energy operation of the main linac with beam, as well as commissioning of the lowest energy matching beamline (splitter) and a partial section of the Fixed Field Alternating gradient (FFA) return loop featuring first production Halbach style permanent magnets. Achieving these tasks required characterization of the injection beam, calibration and phasing of the main linac cavities, demonstration of the required 36 MeV energy gain, and measurement of the splitter line horizontal dispersion and R56 at the nominal 42 MeV. In addition, a procedure for determining the BPM offsets, as well as the tune per cell in the FFA section via scanning the linac energy and inducing betatron oscillations around the periodic orbit in the fractional arc was developed and tested. A detailed comparison of these measurements to simulation is discussed.
△ Less
Submitted 11 February, 2019; v1 submitted 8 February, 2019;
originally announced February 2019.
-
Measurement Techniques for Low Emittance Tuning and Beam Dynamics at CESR
Authors:
M. G. Billing,
J. A. Dobbins,
M. J. Forster,
D. L. Kreinick,
R. E. Meller,
D. P. Peterson,
G. A. Ramirez,
M. C. Rendina,
N. T. Rider,
D. C. Sagan,
J. Shanks,
J. P. Sikora,
M. G. Stedinger,
C. R. Strohman,
H. A. Williams,
M. A. Palmer,
R. L. Holtzapple,
J. Flanagan
Abstract:
After operating as a High Energy Physics electron-positron collider, the Cornell Electron-positron Storage Ring (CESR) has been converted to become a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS). Over the course of several years CESR was adapted for accelerator physics research as a test accelerator, capable of studying topics relevant to future damping…
▽ More
After operating as a High Energy Physics electron-positron collider, the Cornell Electron-positron Storage Ring (CESR) has been converted to become a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS). Over the course of several years CESR was adapted for accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Initially some specific topics were targeted for accelerator physic research with the storage ring in this mode, labeled CesrTA. These topics included 1) tuning techniques to produce low emittance beams, 2) the study of electron cloud (EC) development in a storage ring and 3) intra-beam scattering effects. The complete conversion of CESR to CesrTA occurred over a several year period, described elsewhere. A number of specific instruments were developed for CesrTA. Much of the pre-existing instrumentation was modified to accommodate the scope of these studies and these are described in a companion paper. To complete this research, a number of procedures were developed or modified, often requiring coordinated measurements among different instruments. This paper provides an overview of types of measurements employed for the study of beam dynamics during the operation of CesrTA.
△ Less
Submitted 15 March, 2018; v1 submitted 30 January, 2018;
originally announced January 2018.
-
Instrumentation for the Study of Low Emittance Tuning and Beam Dynamics at CESR
Authors:
M. G. Billing,
J. A. Dobbins,
M. J. Forster,
D. L. Kreinick,
R. E. Meller,
D. P. Peterson,
G. A. Ramirez,
M. C. Rendina,
N. T. Rider,
D. C. Sagan,
J. Shanks,
J. P. Sikora,
M. G. Stedinger,
C. R. Strohman,
H. A. Williams,
M. A. Palmer,
R. L. Holtzapple,
J. Flanagan
Abstract:
The Cornell Electron-positron Storage Ring (CESR) has been converted from a High Energy Physics electron-positron collider to operate as a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS) and to conduct accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Some of the sp…
▽ More
The Cornell Electron-positron Storage Ring (CESR) has been converted from a High Energy Physics electron-positron collider to operate as a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS) and to conduct accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Some of the specific topics that were targeted for the initial phase of operation of the storage ring in this mode for CESR as a Test Accelerator (CesrTA) included 1) tuning techniques to produce low emittance beams, 2) the study of electron cloud development in a storage ring and 3) intra-beam scattering effects. The complete conversion of CESR to CesrTA occurred over a several year period, described elsewhere. In addition to instrumentation for the storage ring, which was created for CesrTA, existing instrumentation was modified to facilitate the entire range of investigations to support these studies. Procedures were developed, often requiring coordinated measurements among different instruments. This paper describes the instruments utilized for the study of beam dynamics during the operation of CesrTA. The treatment of these instruments will remain fairly general in this paper as it focusses on an overview of the instruments themselves. Their interaction and inter-relationships during sequences of observations is found in a companion paper describing the associated measurement techniques. More detailed descriptions and detailed operational performance for some of the instrumentation may be found elsewhere and these will be referenced in the related sections of this paper.
△ Less
Submitted 14 November, 2017; v1 submitted 4 October, 2017;
originally announced October 2017.
-
CBETA Design Report, Cornell-BNL ERL Test Accelerator
Authors:
G. H. Hoffstaetter,
D. Trbojevic,
C. Mayes,
N. Banerjee,
J. Barley,
I. Bazarov,
A. Bartnik,
J. S. Berg,
S. Brooks,
D. Burke,
J. Crittenden,
L. Cultrera,
J. Dobbins,
D. Douglas,
B. Dunham,
R. Eichhorn,
S. Full,
F. Furuta,
C. Franck,
R. Gallagher,
M. Ge,
C. Gulliford,
B. Heltsley,
D. Jusic,
R. Kaplan
, et al. (29 additional authors not shown)
Abstract:
This design report describes the construction plans for the world's first multi-pass SRF ERL. It is a 4-pass recirculating linac that recovers the beam's energy by 4 additional, decelerating passes. All beams are returned for deceleration in a single beam pipe with a large-momentum-aperture permanent magnet FFAG optics. Cornell University has been pioneering a new class of accelerators, Energy Rec…
▽ More
This design report describes the construction plans for the world's first multi-pass SRF ERL. It is a 4-pass recirculating linac that recovers the beam's energy by 4 additional, decelerating passes. All beams are returned for deceleration in a single beam pipe with a large-momentum-aperture permanent magnet FFAG optics. Cornell University has been pioneering a new class of accelerators, Energy Recovery Linacs (ERLs), with a new characteristic set of beam parameters. Technology has been prototyped that is essential for any high brightness electron ERL. This includes a DC electron source and an SRF injector Linac with world-record current and normalized brightness in a bunch train, a high-current linac cryomodule, and a high-power beam stop, and several diagnostics tools for high-current and high-brightness beams. All these are now being used to construct a novel one-cryomodule ERL in Cornell's Wilson Lab. Brookhaven National Laboratory (BNL) has designed a multi-turn ERL for eRHIC, where beam is transported more than 20 times around the 4km long RHIC tunnel. The number of transport lines is minimized by using two arcs with strongly-focusing permanent magnets that can control many beams of different energies. A collaboration between BNL and Cornell has been formed to investigate this multi-turn eRHIC ERL design by building a 4-turn, one-cryomodule ERL at Cornell. It also has a return loop built with strongly focusing permanent magnets and is meant to accelerate 40mA beam to 150MeV. This high-brightness beam will have applications beyond accelerator research, in industry, in nuclear physics, and in X-ray science.
△ Less
Submitted 13 June, 2017;
originally announced June 2017.
-
Beam Position Monitoring System at CESR
Authors:
M. G. Billing,
W. F. Bergan,
M. J. Forster,
R. E. Meller,
M. C. Rendina,
N. T. Rider,
D. C. Sagan,
J. Shanks,
J. P. Sikora,
M. G. Stedinger,
C. R. Strohman,
M. A. Palmer,
R. L. Holtzapple
Abstract:
The Cornell Electron-positron Storage Ring (CESR) has been converted from a High Energy Physics electron-positron collider to operate as a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS) and to conduct accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Some of the sp…
▽ More
The Cornell Electron-positron Storage Ring (CESR) has been converted from a High Energy Physics electron-positron collider to operate as a dedicated synchrotron light source for the Cornell High Energy Synchrotron Source (CHESS) and to conduct accelerator physics research as a test accelerator, capable of studying topics relevant to future damping rings, colliders and light sources. Some of the specific topics that were targeted for the initial phase of operation of the storage ring in this mode, labeled CesrTA (CESR as a Test Accelerator), included 1) tuning techniques to produce low emittance beams, 2) the study of electron cloud development in a storage ring and 3) intra-beam scattering effects. The complete conversion of CESR to CesrTA occurred over a several year period, described elsewhere. As a part of this conversion the CESR beam position monitoring (CBPM) system was completely upgraded to provide the needed instrumental capabilities for these studies. This paper describes the new CBPM system hardware, its function and representative measurements performed by the upgraded system.
△ Less
Submitted 4 August, 2017; v1 submitted 1 June, 2017;
originally announced June 2017.
-
An MDM Spin Transparent Quadrupole for Storage Ring based EDM Search
Authors:
Mei Bai,
Yann Dutheil,
David Sagan
Abstract:
A storage ring provides an attractive option for directly measuring the electric dipole moment~(EDM) of charged particles. To reach a sensitivity of 10^-29 e x cm, it is critical to mitigate the systematic errors from all sources. This daunting task is pushing the precision frontier of accelerator science and technology beyond its current state of the art. Here, we present a unique idea of a magne…
▽ More
A storage ring provides an attractive option for directly measuring the electric dipole moment~(EDM) of charged particles. To reach a sensitivity of 10^-29 e x cm, it is critical to mitigate the systematic errors from all sources. This daunting task is pushing the precision frontier of accelerator science and technology beyond its current state of the art. Here, we present a unique idea of a magnetic dipole moment~(MDM) spin transparent quadrupole that can significantly reduce the systematic errors due to the transverse electric and magnetic fields that particle encounters.
△ Less
Submitted 15 November, 2016;
originally announced November 2016.
-
The Cornell-BNL FFAG-ERL Test Accelerator: White Paper
Authors:
Ivan Bazarov,
John Dobbins,
Bruce Dunham,
Georg Hoffstaetter,
Christopher Mayes,
Ritchie Patterson,
David Sagan,
Ilan Ben-Zvi,
Scott Berg,
Michael Blaskiewicz,
Stephen Brooks,
Kevin Brown,
Wolfram Fischer,
Yue Hao,
Wuzheng Meng,
François Méot,
Michiko Minty,
Stephen Peggs,
Vadim Ptitsin,
Thomas Roser,
Peter Thieberger,
Dejan Trbojevic,
Nick Tsoupas
Abstract:
The Cornell-BNL FFAG-ERL Test Accelerator (C$β$) will comprise the first ever Energy Recovery Linac (ERL) based on a Fixed Field Alternating Gradient (FFAG) lattice. In particular, we plan to use a Non Scaling FFAG (NS-FFAG) lattice that is very compact and thus space- and cost- effective, enabling multiple passes of the electron beam in a single recirculation beam line, using the superconducting…
▽ More
The Cornell-BNL FFAG-ERL Test Accelerator (C$β$) will comprise the first ever Energy Recovery Linac (ERL) based on a Fixed Field Alternating Gradient (FFAG) lattice. In particular, we plan to use a Non Scaling FFAG (NS-FFAG) lattice that is very compact and thus space- and cost- effective, enabling multiple passes of the electron beam in a single recirculation beam line, using the superconducting RF (SRF) linac multiple times. The FFAG-ERL moves the cost optimized linac and recirculation lattice to a dramatically better optimum.
The prime accelerator science motivation for C$β$ is proving that the FFAG-ERL concept works. This is an important milestone for the Brookhaven National Laboratory (BNL) plans to build a major Nuclear Physics facility, eRHIC, based on producing 21 GeV electron beams to collide with the RHIC ion beams. A consequence of the C$β$ work would be the availability of significantly better, cost-effective, compact CW high-brightness electron beams for a plethora of scientific investigations and applications, such as X-ray sources, dark-matter and dark-energy searches, and industrial high-power Free-Electron Laser (FEL) applications.
C$β$ brings together the resources and expertise of a large DOE National Laboratory, BNL, and a leading research university, Cornell. C$β$ will be built in an existing building at Cornell, for the most part using components that have been developed under previous R&D programs, including a fully commissioned world-leading photoemission electron injector, a large SRF accelerator module, and a high-power beam stop. The only elements that require design and construction from scratch is the FFAG magnet transport lattice.
This white paper describes a project that promises to propel high-power, high-brightness electron beam science and applications to an exciting new level.
△ Less
Submitted 2 April, 2015;
originally announced April 2015.
-
Measurement and Compensation of Horizontal Crabbing at the Cornell Electron Storage Ring Test Accelerator
Authors:
M. P. Ehrlichman,
A. Chatterjee,
W. Hartung,
B. Heltsley,
D. P. Peterson,
N. Rider,
D. Rubin,
D. Sagan,
J. P. Shanks,
S. T. Wang
Abstract:
In storage rings, horizontal dispersion in the rf cavities introduces horizontal-longitudinal (xz) coupling, contributing to beam tilt in the xz plane. This coupling can be characterized by a "crabbing" dispersion term ζa that appears in the normal mode decomposition of the 1-turn transfer matrix. ζa is proportional to the rf cavity voltage and the horizontal dispersion in the cavity. We report ex…
▽ More
In storage rings, horizontal dispersion in the rf cavities introduces horizontal-longitudinal (xz) coupling, contributing to beam tilt in the xz plane. This coupling can be characterized by a "crabbing" dispersion term ζa that appears in the normal mode decomposition of the 1-turn transfer matrix. ζa is proportional to the rf cavity voltage and the horizontal dispersion in the cavity. We report experiments at the Cornell Electron Storage Ring Test Accelerator (CesrTA) where xz coupling was explored using three lattices with distinct crabbing properties. We characterize the xz coupling for each case by measuring the horizontal projection of the beam with a beam size monitor. The three lattice configurations correspond to a) 16 mrad xz tilt at the beam size monitor source point, b) compensation of the ζa introduced by one of two pairs of RF cavities with the second, and c) zero dispersion in RF cavities, eliminating ζa entirely. Additionally, intrabeam scattering (IBS) is evident in our measurements of beam size vs. rf voltage.
△ Less
Submitted 13 March, 2014; v1 submitted 7 November, 2013;
originally announced November 2013.
-
Characterization of the International Linear Collider damping ring optics
Authors:
James Shanks,
Dave Rubin,
David Sagan
Abstract:
A method is presented for characterizing the emittance dilution and dynamic aperture for an arbitrary closed lattice that includes guide field magnet errors, multipole errors and misalignments. This method, developed and tested at the Cornell Electron Storage Ring Test Accelerator (CesrTA), has been applied to the damping ring lattice for the International Linear Collider (ILC). The effectiveness…
▽ More
A method is presented for characterizing the emittance dilution and dynamic aperture for an arbitrary closed lattice that includes guide field magnet errors, multipole errors and misalignments. This method, developed and tested at the Cornell Electron Storage Ring Test Accelerator (CesrTA), has been applied to the damping ring lattice for the International Linear Collider (ILC). The effectiveness of beam based emittance tuning is limited by beam position monitor (BPM) measurement errors, number of corrector magnets and their placement, and correction algorithm. The specifications for damping ring magnet alignment, multipole errors, number of BPMs, and precision in BPM measurements are shown to be consistent with the required emittances and dynamic aperture. The methodology is then used to determine the minimum number of position monitors that is required to achieve the emittance targets, and how that minimum depends on the location of the BPMs. Similarly, the maximum tolerable multipole errors are evaluated. Finally, the robustness of each BPM configuration with respect to random failures is explored.
△ Less
Submitted 4 September, 2014; v1 submitted 9 September, 2013;
originally announced September 2013.
-
Low-emittance tuning at the Cornell Electron Storage Ring
Authors:
James Shanks,
Dave Rubin,
David Sagan
Abstract:
In 2008 the Cornell Electron/Positron Storage Ring (CESR) was reconfigured from an electron/positron collider to serve as a testbed for the International Linear Collider (ILC) damping rings. One of the primary goals of the CESR Test Accelerator (CesrTA) project is to develop a fast low-emittance tuning method which scales well to large rings such as the ILC damping rings, and routinely achieves a…
▽ More
In 2008 the Cornell Electron/Positron Storage Ring (CESR) was reconfigured from an electron/positron collider to serve as a testbed for the International Linear Collider (ILC) damping rings. One of the primary goals of the CESR Test Accelerator (CesrTA) project is to develop a fast low-emittance tuning method which scales well to large rings such as the ILC damping rings, and routinely achieves a vertical emittance of order 10 pm at 2.085 GeV. This paper discusses the tuning methods developed at CesrTA to achieve low-emittance conditions. One iteration of beam-based measurement and correction requires about 10 minutes. A minimum vertical emittance of 10.3 +3.2/-3.4(sys) +/-0.2(stat) pm has been achieved at 2.085 GeV. In various configurations and beam energies the correction technique routinely achieves vertical emittance around 10 pm after correction, with RMS coupling < 0.5%. The measured vertical dispersion is dominated by beam position monitor systematics. The propagation of uncertainties in the emittance measurement is described in detail. Simulations modeling the effects of magnet misalignments, BPM errors, and emittance correction algorithm suggest the residual vertical emittance measured at the conclusion of the tuning procedure is dominated by sources other than optics errors and misalignments.
△ Less
Submitted 2 April, 2014; v1 submitted 9 September, 2013;
originally announced September 2013.
-
Intrabeam Scattering Studies at CesrTA
Authors:
M. P. Ehrlichman,
W. Hartung,
B. Heltsley,
D. P. Peterson,
N. Rider,
D. Rubin,
D. Sagan,
J. Shanks,
S. T. Wang,
R. Campbell,
R. Holtzapple
Abstract:
Intrabeam scattering (IBS) limits the emittance and single-bunch current that can be achieved in electron or positron storage ring colliders, damping rings, and light sources. Much theoretical work on IBS exists, and while the theories have been validated in hadron and ion machines, the presence of strong damping makes IBS in lepton machines a different phenomenon. We present the results of measur…
▽ More
Intrabeam scattering (IBS) limits the emittance and single-bunch current that can be achieved in electron or positron storage ring colliders, damping rings, and light sources. Much theoretical work on IBS exists, and while the theories have been validated in hadron and ion machines, the presence of strong damping makes IBS in lepton machines a different phenomenon. We present the results of measurements at CesrTA of IBS dominated beams, and compare the data with theory. The beams we study have parameters typical of those specified for the next generation of wiggler dominated storage rings: low emittance, small bunch length, and few GeV energy. Our measurements are in good agreement with IBS theory, provided a tail-cut procedure is applied.
△ Less
Submitted 14 October, 2013; v1 submitted 31 July, 2013;
originally announced August 2013.
-
Extended 1D Method for Coherent Synchrotron Radiation including Shielding
Authors:
David Sagan,
Georg Hoffstaetter,
Christopher Mayes,
Udom Sae-Ueng
Abstract:
Coherent Synchrotron Radiation can severely limit the performance of accelerators designed for high brightness and short bunch length. Examples include light sources based on ERLs or FELs, and bunch compressors for linear colliders. In order to better simulate Coherent Synchrotron Radiation, the established 1-dimensional formalism is extended to work at lower energies, at shorter bunch lengths,…
▽ More
Coherent Synchrotron Radiation can severely limit the performance of accelerators designed for high brightness and short bunch length. Examples include light sources based on ERLs or FELs, and bunch compressors for linear colliders. In order to better simulate Coherent Synchrotron Radiation, the established 1-dimensional formalism is extended to work at lower energies, at shorter bunch lengths, and for an arbitrary configuration of multiple bends. Wide vacuum chambers are simulated by means of vertical image charges. This formalism has been implemented in the general beam dynamics code "Bmad" and its results are here compared to analytical approximations, to numerical solutions of the Maxwell equations, and to the simulation code "elegant".
△ Less
Submitted 17 June, 2008;
originally announced June 2008.