Showing 1–15 of 15 results for author: Polonelli, T

Aerodynamic Performance and Impact Analysis of a MEMS-Based Non-Invasive Monitoring System for Wind Turbine Blades

Authors: Nicolas Schärer, Denis Mikhaylov, Cédric Sievi, Badoui Hanna, Caroline Braud, Julien Deparday, Sarah Barber, Tommaso Polonelli, Michele Magno

Abstract: Wind power generation plays a crucial role in transitioning away from fossil fuel-dependent energy sources, contributing significantly to the mitigation of climate change. Monitoring and evaluating the aerodynamics of large wind turbine rotors is crucial to enable more wind energy deployment. This is necessary to achieve the European climate goal of a reduction in net greenhouse gas emissions by a… ▽ More Wind power generation plays a crucial role in transitioning away from fossil fuel-dependent energy sources, contributing significantly to the mitigation of climate change. Monitoring and evaluating the aerodynamics of large wind turbine rotors is crucial to enable more wind energy deployment. This is necessary to achieve the European climate goal of a reduction in net greenhouse gas emissions by at least 55% by 2030, compared to 1990 levels. This paper presents a comparison between two measurement systems for evaluating the aerodynamic performance of wind turbine rotor blades on a full-scale wind tunnel test. One system uses an array of ten commercial compact ultra-low power micro-electromechanical systems (MEMS) pressure sensors placed on the blade surface, while the other employs high-accuracy lab-based pressure scanners embedded in the airfoil. The tests are conducted at a Reynolds number of 3.5 x 10^6, which represents typical operating conditions for wind turbines. MEMS sensors are of particular interest, as they can enable real-time monitoring which would be impossible with the ground truth system. This work provides an accurate quantification of the impact of the MEMS system on the blade aerodynamics and its measurement accuracy. Our results indicate that MEMS sensors, with a total sensing power below 1.6 mW, can measure key aerodynamic parameters like Angle of Attack (AoA) and flow separation with a precision of 1°. Although there are minor differences in measurements due to sensor encapsulation, the MEMS system does not significantly compromise blade aerodynamics, with a maximum shift in the angle of attack for flow separation of only 1°. These findings indicate that surface and low-power MEMS sensor systems are a promising approach for efficient and sustainable wind turbine monitoring using self-sustaining Internet of Things devices and wireless sensor networks. △ Less

Submitted 21 August, 2024; originally announced August 2024.

H-Watch: An Open, Connected Platform for AI-Enhanced COVID19 Infection Symptoms Monitoring and Contact Tracing

Authors: Tommaso Polonelli, Lukas Schulthess, Philipp Mayer, Michele Magno, Luca Benini

Abstract: The novel COVID-19 disease has been declared a pandemic event. Early detection of infection symptoms and contact tracing are playing a vital role in containing COVID-19 spread. As demonstrated by recent literature, multi-sensor and connected wearable devices might enable symptom detection and help tracing contacts, while also acquiring useful epidemiological information. This paper presents the de… ▽ More The novel COVID-19 disease has been declared a pandemic event. Early detection of infection symptoms and contact tracing are playing a vital role in containing COVID-19 spread. As demonstrated by recent literature, multi-sensor and connected wearable devices might enable symptom detection and help tracing contacts, while also acquiring useful epidemiological information. This paper presents the design and implementation of a fully open-source wearable platform called H-Watch. It has been designed to include several sensors for COVID-19 early detection, multi-radio for wireless transmission and tracking, a microcontroller for processing data on-board, and finally, an energy harvester to extend the battery lifetime. Experimental results demonstrated only 5.9 mW of average power consumption, leading to a lifetime of 9 days on a small watch battery. Finally, all the hardware and the software, including a machine learning on MCU toolkit, are provided open-source, allowing the research community to build and use the H-Watch. △ Less

Submitted 31 July, 2024; originally announced July 2024.

Ultra-Lightweight Collaborative Mapping for Robot Swarms

Authors: Vlad Niculescu, Tommaso Polonelli, Michele Magno, Luca Benini

Abstract: A key requirement in robotics is the ability to simultaneously self-localize and map a previously unknown environment, relying primarily on onboard sensing and computation. Achieving fully onboard accurate simultaneous localization and mapping (SLAM) is feasible for high-end robotic platforms, whereas small and inexpensive robots face challenges due to constrained hardware, therefore frequently re… ▽ More A key requirement in robotics is the ability to simultaneously self-localize and map a previously unknown environment, relying primarily on onboard sensing and computation. Achieving fully onboard accurate simultaneous localization and mapping (SLAM) is feasible for high-end robotic platforms, whereas small and inexpensive robots face challenges due to constrained hardware, therefore frequently resorting to external infrastructure for sensing and computation. The challenge is further exacerbated in swarms of robots, where coordination, scalability, and latency are crucial concerns. This work introduces a decentralized and lightweight collaborative SLAM approach that enables mapping on virtually any robot, even those equipped with low-cost hardware and only 1.5 MB of memory, including miniaturized insect-size devices. Moreover, the proposed solution supports large swarm formations with the capability to coordinate hundreds of agents. To substantiate our claims, we have successfully implemented collaborative SLAM on centimeter-size drones weighing 46 g. Remarkably, we achieve a mapping accuracy below 30 cm, a result comparable to high-end state-of-the-art solutions while reducing the cost, memory, and computation requirements by two orders of magnitude. Our approach is innovative in three main aspects. First, it enables onboard infrastructure-less collaborative mapping with a lightweight and cost-effective (\$20) solution in terms of sensing and computation. Second, we optimize the data traffic within the swarm to support hundreds of cooperative agents using standard wireless protocols such as ultra-wideband (UWB), Bluetooth, or WiFi. Last, we implement a distributed swarm coordination policy to decrease mapping latency and enhance accuracy. △ Less

Submitted 26 August, 2024; v1 submitted 3 July, 2024; originally announced July 2024.

Comments: 14 pages, 13 figures

Angle of Arrival and Centimeter Distance Estimation on a Smart UWB Sensor Node

Authors: Tobias Margiani, Silvano Cortesi, Milena Keller, Christian Vogt, Tommaso Polonelli, Michele Magno

Abstract: Accurate and low-power indoor localization is becoming more and more of a necessity to empower novel consumer and industrial applications. In this field, the most promising technology is based on UWB modulation; however, current UWB positioning systems do not reach centimeter accuracy in general deployments due to multipath and nonisotropic antennas, still necessitating several fixed anchors to es… ▽ More Accurate and low-power indoor localization is becoming more and more of a necessity to empower novel consumer and industrial applications. In this field, the most promising technology is based on UWB modulation; however, current UWB positioning systems do not reach centimeter accuracy in general deployments due to multipath and nonisotropic antennas, still necessitating several fixed anchors to estimate an object's position in space. This article presents an in-depth study and assessment of angle of arrival (AoA) UWB measurements using a compact, low-power solution integrating a novel commercial module with phase difference of arrival (PDoA) estimation as integrated feature. Results demonstrate the possibility of reaching centimeter distance precision and ang 2.4 average angular accuracy in many operative conditions, e.g., in a ang 90 range around the center. Moreover, integrating the channel impulse response, the phase differential of arrival, and the point-to-point distance, an error correction model is discussed to compensate for reflections, multipaths, and front-back ambiguity. △ Less

Submitted 21 December, 2023; originally announced December 2023.

Comments: This article has been accepted for publication in the IEEE Transactions on Instrumentation and Measurement journal. DOI: https://doi.org/10.1109/TIM.2023.3282289

NanoSLAM: Enabling Fully Onboard SLAM for Tiny Robots

Authors: Vlad Niculescu, Tommaso Polonelli, Michele Magno, Luca Benini

Abstract: Perceiving and mapping the surroundings are essential for enabling autonomous navigation in any robotic platform. The algorithm class that enables accurate mapping while correcting the odometry errors present in most robotics systems is Simultaneous Localization and Mapping (SLAM). Today, fully onboard mapping is only achievable on robotic platforms that can host high-wattage processors, mainly du… ▽ More Perceiving and mapping the surroundings are essential for enabling autonomous navigation in any robotic platform. The algorithm class that enables accurate mapping while correcting the odometry errors present in most robotics systems is Simultaneous Localization and Mapping (SLAM). Today, fully onboard mapping is only achievable on robotic platforms that can host high-wattage processors, mainly due to the significant computational load and memory demands required for executing SLAM algorithms. For this reason, pocket-size hardware-constrained robots offload the execution of SLAM to external infrastructures. To address the challenge of enabling SLAM algorithms on resource-constrained processors, this paper proposes NanoSLAM, a lightweight and optimized end-to-end SLAM approach specifically designed to operate on centimeter-size robots at a power budget of only 87.9 mW. We demonstrate the mapping capabilities in real-world scenarios and deploy NanoSLAM on a nano-drone weighing 44 g and equipped with a novel commercial RISC-V low-power parallel processor called GAP9. The algorithm is designed to leverage the parallel capabilities of the RISC-V processing cores and enables mapping of a general environment with an accuracy of 4.5 cm and an end-to-end execution time of less than 250 ms. △ Less

Submitted 21 September, 2023; originally announced September 2023.

Comments: 23 pages

Fully Onboard SLAM for Distributed Mapping with a Swarm of Nano-Drones

Authors: Carl Friess, Vlad Niculescu, Tommaso Polonelli, Michele Magno, Luca Benini

Abstract: The use of Unmanned Aerial Vehicles (UAVs) is rapidly increasing in applications ranging from surveillance and first-aid missions to industrial automation involving cooperation with other machines or humans. To maximize area coverage and reduce mission latency, swarms of collaborating drones have become a significant research direction. However, this approach requires open challenges in positionin… ▽ More The use of Unmanned Aerial Vehicles (UAVs) is rapidly increasing in applications ranging from surveillance and first-aid missions to industrial automation involving cooperation with other machines or humans. To maximize area coverage and reduce mission latency, swarms of collaborating drones have become a significant research direction. However, this approach requires open challenges in positioning, mapping, and communications to be addressed. This work describes a distributed mapping system based on a swarm of nano-UAVs, characterized by a limited payload of 35 g and tightly constrained on-board sensing and computing capabilities. Each nano-UAV is equipped with four 64-pixel depth sensors that measure the relative distance to obstacles in four directions. The proposed system merges the information from the swarm and generates a coherent grid map without relying on any external infrastructure. The data fusion is performed using the iterative closest point algorithm and a graph-based simultaneous localization and mapping algorithm, running entirely on-board the UAV's low-power ARM Cortex-M microcontroller with just 192 kB of SRAM memory. Field results gathered in three different mazes from a swarm of up to 4 nano-UAVs prove a mapping accuracy of 12 cm and demonstrate that the mapping time is inversely proportional to the number of agents. The proposed framework scales linearly in terms of communication bandwidth and on-board computational complexity, supporting communication between up to 20 nano-UAVs and mapping of areas up to 180 m2 with the chosen configuration requiring only 50 kB of memory. △ Less

Submitted 7 September, 2023; originally announced September 2023.

Exploring Automatic Gym Workouts Recognition Locally On Wearable Resource-Constrained Devices

Authors: Sizhen Bian, Xiaying Wang, Tommaso Polonelli, Michele Magno

Abstract: Automatic gym activity recognition on energy- and resource-constrained wearable devices removes the human-interaction requirement during intense gym sessions - like soft-touch tapping and swiping. This work presents a tiny and highly accurate residual convolutional neural network that runs in milliwatt microcontrollers for automatic workouts classification. We evaluated the inference performance o… ▽ More Automatic gym activity recognition on energy- and resource-constrained wearable devices removes the human-interaction requirement during intense gym sessions - like soft-touch tapping and swiping. This work presents a tiny and highly accurate residual convolutional neural network that runs in milliwatt microcontrollers for automatic workouts classification. We evaluated the inference performance of the deep model with quantization on three resource-constrained devices: two microcontrollers with ARM-Cortex M4 and M7 core from ST Microelectronics, and a GAP8 system on chip, which is an open-sourced, multi-core RISC-V computing platform from GreenWaves Technologies. Experimental results show an accuracy of up to 90.4% for eleven workouts recognition with full precision inference. The paper also presents the trade-off performance of the resource-constrained system. While keeping the recognition accuracy (88.1%) with minimal loss, each inference takes only 3.2 ms on GAP8, benefiting from the 8 RISC-V cluster cores. We measured that it features an execution time that is 18.9x and 6.5x faster than the Cortex-M4 and Cortex-M7 cores, showing the feasibility of real-time on-board workouts recognition based on the described data set with 20 Hz sampling rate. The energy consumed for each inference on GAP8 is 0.41 mJ compared to 5.17 mJ on Cortex-M4 and 8.07 mJ on Cortex-M7 with the maximum clock. It can lead to longer battery life when the system is battery-operated. We also introduced an open data set composed of fifty sessions of eleven gym workouts collected from ten subjects that is publicly available. △ Less

Submitted 13 January, 2023; originally announced January 2023.

Fully On-board Low-Power Localization with Multizone Time-of-Flight Sensors on Nano-UAVs

Authors: Hanna Müller, Nicky Zimmerman, Tommaso Polonelli, Michele Magno, Jens Behley, Cyrill Stachniss, Luca Benini

Abstract: Nano-size unmanned aerial vehicles (UAVs) hold enormous potential to perform autonomous operations in complex environments, such as inspection, monitoring or data collection. Moreover, their small size allows safe operation close to humans and agile flight. An important part of autonomous flight is localization, which is a computationally intensive task especially on a nano-UAV that usually has st… ▽ More Nano-size unmanned aerial vehicles (UAVs) hold enormous potential to perform autonomous operations in complex environments, such as inspection, monitoring or data collection. Moreover, their small size allows safe operation close to humans and agile flight. An important part of autonomous flight is localization, which is a computationally intensive task especially on a nano-UAV that usually has strong constraints in sensing, processing and memory. This work presents a real-time localization approach with low element-count multizone range sensors for resource-constrained nano-UAVs. The proposed approach is based on a novel miniature 64-zone time-of-flight sensor from ST Microelectronics and a RISC-V-based parallel ultra low-power processor, to enable accurate and low latency Monte Carlo Localization on-board. Experimental evaluation using a nano-UAV open platform demonstrated that the proposed solution is capable of localizing on a 31.2m$\boldsymbol{^2}$ map with 0.15m accuracy and an above 95% success rate. The achieved accuracy is sufficient for localization in common indoor environments. We analyze tradeoffs in using full and half-precision floating point numbers as well as a quantized map and evaluate the accuracy and memory footprint across the design space. Experimental evaluation shows that parallelizing the execution for 8 RISC-V cores brings a 7x speedup and allows us to execute the algorithm on-board in real-time with a latency of 0.2-30ms (depending on the number of particles), while only increasing the overall drone power consumption by 3-7%. Finally, we provide an open-source implementation of our approach. △ Less

Submitted 25 November, 2022; originally announced December 2022.

Comments: DATE 2023

Robust and Efficient Depth-based Obstacle Avoidance for Autonomous Miniaturized UAVs

Authors: Hanna Müller, Vlad Niculescu, Tommaso Polonelli, Michele Magno, Luca Benini

Abstract: Nano-size drones hold enormous potential to explore unknown and complex environments. Their small size makes them agile and safe for operation close to humans and allows them to navigate through narrow spaces. However, their tiny size and payload restrict the possibilities for on-board computation and sensing, making fully autonomous flight extremely challenging. The first step towards full autono… ▽ More Nano-size drones hold enormous potential to explore unknown and complex environments. Their small size makes them agile and safe for operation close to humans and allows them to navigate through narrow spaces. However, their tiny size and payload restrict the possibilities for on-board computation and sensing, making fully autonomous flight extremely challenging. The first step towards full autonomy is reliable obstacle avoidance, which has proven to be technically challenging by itself in a generic indoor environment. Current approaches utilize vision-based or 1-dimensional sensors to support nano-drone perception algorithms. This work presents a lightweight obstacle avoidance system based on a novel millimeter form factor 64 pixels multi-zone Time-of-Flight (ToF) sensor and a generalized model-free control policy. Reported in-field tests are based on the Crazyflie 2.1, extended by a custom multi-zone ToF deck, featuring a total flight mass of 35g. The algorithm only uses 0.3% of the on-board processing power (210uS execution time) with a frame rate of 15fps, providing an excellent foundation for many future applications. Less than 10% of the total drone power is needed to operate the proposed perception system, including both lifting and operating the sensor. The presented autonomous nano-size drone reaches 100% reliability at 0.5m/s in a generic and previously unexplored indoor environment. The proposed system is released open-source with an extensive dataset including ToF and gray-scale camera data, coupled with UAV position ground truth from motion capture. △ Less

Submitted 26 August, 2022; originally announced August 2022.

Comments: This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may no longer be accessible

Aerosense: A Self-Sustainable And Long-Range Bluetooth Wireless Sensor Node for Aerodynamic and Aeroacoustic Monitoring on Wind Turbines

Authors: Tommaso Polonelli, Hanna Müller, Weikang Kong, Raphael Fischer, Luca Benini, Michele Magno

Abstract: This paper presents a low-power, self-sustainable, and modular wireless sensor node for aerodynamic and acoustic measurements on wind turbines and other industrial structures. It includes 40 high-accuracy barometers, 10 microphones, 5 differential pressure sensors, and implements a lossy and a lossless on-board data compression algorithm to decrease the transmission energy cost. The wireless trans… ▽ More This paper presents a low-power, self-sustainable, and modular wireless sensor node for aerodynamic and acoustic measurements on wind turbines and other industrial structures. It includes 40 high-accuracy barometers, 10 microphones, 5 differential pressure sensors, and implements a lossy and a lossless on-board data compression algorithm to decrease the transmission energy cost. The wireless transmitter is based on Bluetooth Low Energy 5.1 tuned for long-range and high throughput while maintaining adequate per-bit energy efficiency (80 nJ). Moreover, we field-assessed the node capability to collect precise and accurate aerodynamic data. Outdoor experimental tests revealed that the system can acquire and sustain a data rate of 850 kbps over 438 m. The power consumption while collecting and streaming all measured data is 120 mW, enabling self-sustainability and long-term in-situ monitoring with a 111 cm^2 photovoltaic panel. △ Less

Submitted 24 May, 2022; originally announced May 2022.

Comments: 9 pages, 4 figures, 3 tables, IEEE Journal

Embedding Temporal Convolutional Networks for Energy-Efficient PPG-Based Heart Rate Monitoring

Authors: Alessio Burrello, Daniele Jahier Pagliari, Pierangelo Maria Rapa, Matilde Semilia, Matteo Risso, Tommaso Polonelli, Massimo Poncino, Luca Benini, Simone Benatti

Abstract: Photoplethysmography (PPG) sensors allow for non-invasive and comfortable heart-rate (HR) monitoring, suitable for compact wrist-worn devices. Unfortunately, Motion Artifacts (MAs) severely impact the monitoring accuracy, causing high variability in the skin-to-sensor interface. Several data fusion techniques have been introduced to cope with this problem, based on combining PPG signals with inert… ▽ More Photoplethysmography (PPG) sensors allow for non-invasive and comfortable heart-rate (HR) monitoring, suitable for compact wrist-worn devices. Unfortunately, Motion Artifacts (MAs) severely impact the monitoring accuracy, causing high variability in the skin-to-sensor interface. Several data fusion techniques have been introduced to cope with this problem, based on combining PPG signals with inertial sensor data. Until know, both commercial and reasearch solutions are computationally efficient but not very robust, or strongly dependent on hand-tuned parameters, which leads to poor generalization performance. % In this work, we tackle these limitations by proposing a computationally lightweight yet robust deep learning-based approach for PPG-based HR estimation. Specifically, we derive a diverse set of Temporal Convolutional Networks (TCN) for HR estimation, leveraging Neural Architecture Search (NAS). Moreover, we also introduce ActPPG, an adaptive algorithm that selects among multiple HR estimators depending on the amount of MAs, to improve energy efficiency. We validate our approaches on two benchmark datasets, achieving as low as 3.84 Beats per Minute (BPM) of Mean Absolute Error (MAE) on PPGDalia, which outperforms the previous state-of-the-art. Moreover, we deploy our models on a low-power commercial microcontroller (STM32L4), obtaining a rich set of Pareto optimal solutions in the complexity vs. accuracy space. △ Less

Submitted 1 March, 2022; originally announced March 2022.

Structural Health Monitoring system with Narrowband IoT and MEMS sensors

Authors: Flavio Di Nuzzo, Davide Brunelli, Tommaso Polonelli, Luca Benini

Abstract: Monitoring of civil infrastructures is critically needed to track aging, damages and ultimately to prevent severe failures which can endanger many lives. The ability to monitor in a continuous and fine-grained fashion the integrity of a wide variety of buildings, referred to as structural health monitoring, with low-cost, long-term and continuous measurements is essential from both an economic and… ▽ More Monitoring of civil infrastructures is critically needed to track aging, damages and ultimately to prevent severe failures which can endanger many lives. The ability to monitor in a continuous and fine-grained fashion the integrity of a wide variety of buildings, referred to as structural health monitoring, with low-cost, long-term and continuous measurements is essential from both an economic and a life-safety standpoint. To address these needs, we propose a low-cost wireless sensor node specifically designed to support modal analysis over extended periods of time with long-range connectivity at low power consumption. Our design uses very cost-effective MEMS accelerometers and exploits the Narrowband IoT protocol (NB-IoT) to establish long-distance connection with 4G infrastructure networks. Long-range wireless connectivity, cabling-free installation and multi-year lifetime are a unique combination of features, not available, to the best of our knowledge, in any commercial or research device. We discuss in detail the hardware architecture and power management of the node. Experimental tests demonstrate a lifetime of more than ten years with a 17000 mAh battery or completely energy-neutral operation with a small solar panel (60 mm x 120 mm). Further, we validate measurement accuracy and confirm the feasibility of modal analysis with the MEMS sensors: compared with a high-precision instrument based on a piezoelectric transducer, our sensor node achieves a maximum difference of 0.08% at a small fraction of the cost and power consumption. △ Less

Submitted 27 April, 2021; originally announced April 2021.

Comments: 10 pages, 10 figures, IEEE Sensors Journal

Slotted ALOHA on LoRaWAN - Design, Analysis, and Deployment

Authors: Tommaso Polonelli, Davide Brunelli, Achille Marzocchi, Luca Benini

Abstract: LoRaWAN is one of the most promising standards for long-range sensing applications. However, the high number of end devices expected in at-scale deployment, combined with the absence of an effective synchronization scheme, challenge the scalability of this standard. In this paper, we present an approach to increase network throughput through a Slotted-ALOHA overlay on LoRaWAN networks. To increase… ▽ More LoRaWAN is one of the most promising standards for long-range sensing applications. However, the high number of end devices expected in at-scale deployment, combined with the absence of an effective synchronization scheme, challenge the scalability of this standard. In this paper, we present an approach to increase network throughput through a Slotted-ALOHA overlay on LoRaWAN networks. To increase the single channel capacity, we propose to regulate the communication of LoRaWAN networks using a Slotted-ALOHA variant on the top of the Pure-ALOHA approach used by the standard; thus, no modification in pre-existing libraries is necessary. Our method is based on an innovative synchronization service that is suitable for low-cost wireless sensor nodes. We modelled the LoRaWAN channel with extensive measurement on hardware platforms, and we quantified the impact of tuning parameters on physical and medium access control layers, as well as the packet collision rate. Results show that Slotted-ALOHA supported by our synchronization service significantly improves the performance of traditional LoRaWAN networks regarding packet loss rate and network throughput. △ Less

Submitted 18 February, 2019; originally announced February 2019.

Comments: 19 pages

Journal ref: Special Issue "Low Energy Wireless Sensor Networks: Protocols, Architectures and Solutions" January 2019

A LoRaWAN Wireless Sensor Network for Data Center Temperature Monitoring

Authors: Tommaso Polonelli, Davide Brunelli, Andrea Bartolini, Luca Benini

Abstract: High-performance computing installations, which are at the basis of web and cloud servers as well as supercomputers, are constrained by two main conflicting requirements: IT power consumption generated by the computing nodes and the heat that must be removed to avoid thermal hazards. In the worst cases, up to 60% of the energy consumed in a data center is used for cooling, often related to an over… ▽ More High-performance computing installations, which are at the basis of web and cloud servers as well as supercomputers, are constrained by two main conflicting requirements: IT power consumption generated by the computing nodes and the heat that must be removed to avoid thermal hazards. In the worst cases, up to 60% of the energy consumed in a data center is used for cooling, often related to an over-designed cooling system. We propose a low-cost and battery-supplied wireless sensor network (WSN) for fine-grained, flexible and long-term data center temperature monitoring. The WSN has been operational collecting more than six million data points, with no losses, for six months without battery recharges. Our work reaches a 300x better energy efficiency than the previously reported WSNs for similar scenarios and on a 7x wider area. The data collected by the network can be used to optimize cooling effort while avoiding dangerous hot spots. △ Less

Submitted 18 February, 2019; originally announced February 2019.

Comments: 9 pages

Slotted ALOHA Overlay on LoRaWAN: a Distributed Synchronization Approach

Authors: Tommaso Polonelli, Davide Brunelli, Luca Benini

Abstract: LoRaWAN is one of the most promising standards for IoT applications. Nevertheless, the high density of end-devices expected for each gateway, the absence of an effective synchronization scheme between gateway and end-devices, challenge the scalability of these networks. In this article, we propose to regulate the communication of LoRaWAN networks using a Slotted-ALOHA (S-ALOHA) instead of the clas… ▽ More LoRaWAN is one of the most promising standards for IoT applications. Nevertheless, the high density of end-devices expected for each gateway, the absence of an effective synchronization scheme between gateway and end-devices, challenge the scalability of these networks. In this article, we propose to regulate the communication of LoRaWAN networks using a Slotted-ALOHA (S-ALOHA) instead of the classic ALOHA approach used by LoRa. The implementation is an overlay on top of the standard LoRaWAN; thus no modification in pre-existing LoRaWAN firmware and libraries is necessary. Our method is based on a novel distributed synchronization service that is suitable for low-cost IoT end-nodes. S-ALOHA supported by our synchronization service significantly improves the performance of traditional LoRaWAN networks regarding packet loss rate and network throughput. △ Less

Submitted 6 September, 2018; originally announced September 2018.

Comments: 4 pages, 8 figures